Verlichte US-toetsenbord voor HP ProBook 450 455 G6 en G7
SKU: 99895715517

Verlichte US-toetsenbord voor HP ProBook 450 455 G6 en G7

$32.04 $35.60
Save 10%
No.2 Bestseller on www.maison-nature-brenne.fr >

Shipping Estimate
USA
  • USA
  • CAN

Ships within 48 hours · Estimated delivery Jul 9 - Jul 14

Promo Codes Available:

For Your Every Summer RSVP, with Code: SUMMER15

Description

Verlichte US-toetsenbord voor HP ProBook 450 455 G6 en G7Reageren toetsen niet meer of werkt de backlight van je HP ProBook 450 455 G6 of G7 niet? Dit verlichte US toetsenbord is een directe vervanger inclusief verlichting. Past op de G6 en G7 generaties. Specificaties Onderdeeltype: Laptoptoetsenbord met achtergrondverlichting Lay out: US (QWERTY) Aansluiting: Originele flex connector Kwaliteit: 100% getest en werkend Levering: Los toetsenbord Compatibele modellen: HP ProBook 450 G6, ProBook 455 G6,

Reageren toetsen niet meer of werkt de backlight van je HP ProBook 450/455 G6 of G7 niet? Dit verlichte US-toetsenbord is een directe vervanger inclusief verlichting. Past op de G6 en G7 generaties.

Specificaties

  • Onderdeeltype: Laptoptoetsenbord met achtergrondverlichting
  • Lay-out: US (QWERTY)
  • Aansluiting: Originele flex-connector
  • Kwaliteit: 100% getest en werkend
  • Levering: Los toetsenbord
  • Compatibele modellen: HP ProBook 450 G6, ProBook 455 G6, ProBook 450 G7, ProBook 455 G7

Symptomen van een defect toetsenbord

  • Toetsen reageren niet of typen dubbel
  • Backlight werkt niet of flikkert
  • Vloeistofschade onder toetsen
  • Toetsen blijven hangen
  • Verkeerde tekens bij typen

Installatie

🟡 Moeilijkheidsgraad: gemiddeld · ~40 minuten · Gereedschap: Phillips-schroevendraaier, Plastic spudger, Pincet.

Veelgestelde vragen

Past dit op de ProBook 440 G6 ook?
Nee, alleen op de 15-inch 450/455 G6/G7. De 440 is een ander 14-inch model.

Werkt het backlight direct?
Ja, geen extra installatie nodig. Met Fn+toets regel je het verlichtingsniveau.

Hoe weet ik welke versie ik nu heb?
Open Fn+F5 (of vergelijkbaar): werkt de verlichting niet, dan heb je de niet-verlichte variant en moet je het backlight-model bestellen.

Shipping Notes
  • Free Standard Shipping on $100+ Orders to the USA.
  • Except Preorder products are shipped in 48 hours.
  • Delivery to the USA:
  1. Standard Shipping : 3-10 business days
  • If time is of the essence, please consider selecting expedited delivery for faster service.
Exchange/Return Notes
  • We offer a 30-day return/exchange service after receiving.
  • Final sale items are not eligible for returns or exchanges.
  • To process your return/exchange, please contact us at [email protected]
  • Please click here for more details>>> Return & Exchange Policy
SKU: 99895715517

Discover Niche Categories That Outsell

Top-Converting Item to Boost Your Average Order

4.6 ★★★★★
Based on 1107 reviews
Sort
Highest Rating
Newest First
Oldest First
Product Reviews
P
Verified Purchase
Peter Schott
Battle Creek, US
★★★★★ 5
Use the best oil to protect your investment
Configuration: 4-Stroke, Size: 1 GA
Great product.
WAS THIS REVIEW HELPFUL?YesReportShare
Reviewed in the United States on September 30, 2025
S
Verified Purchase
Steve M.
Lake Worth, US
★★★★★ 5
Works well. You need to drill a 3/8” hole
Appears to be well made, alignment bar slides in nicely. As stated, you need to drill a hole in the bar for the gimble bearing driver, the directions are not clear, what I did was before I take out the old gimble bearing, put an O ring on the bar close to the last step on the bar, slide the bar all the way in, then carefully slide the bar out, this marks the distance from the back of the gimble bearing to where the shaft on the outdrive bottoms out, move the O ring a 1/4” towards the stepped part of the alignment tool (this is so you won’t bottom out the alignment tool when driving the gimble bearing in) then slide the driver puck up to the O ring and use a 3/8” diameter transfer punch through the side hole in the puck to mark the bar. You need to drill a 3/8” diameter hole in the alignment bar, two V blocks, some clamps, and a drill press will make drilling much easier, after the bar is securely mounted and centered in the drill press, use a center drill, then 1/4” drill first, using plenty of oil, drill all the way through, then use the 3/8” drill, deburr both sides and you should be good to go. People complain that it doesn’t come pre-drilled, the reason is that not all out drives are the same so you have to fit it to the outdrive that you have. Fortunately, I have a machine shop at my house and have a jig setup with various drill bushings, but the method I described above should work for you. Just make sure you’re perfectly centered and secure before you start drilling.
WAS THIS REVIEW HELPFUL?YesReportShare
Reviewed in the United States on April 16, 2026
N
Verified Purchase
Nancy filippi
Fort Morgan, US
★★★★★ 5
A must pull your gimbal bearing
You do need to drill a hole but worked perfect
WAS THIS REVIEW HELPFUL?YesReportShare
Reviewed in the United States on December 26, 2025
R
Verified Purchase
rich911s
New York, US
★★★★★ 5
Worked for Volvo Penta SX Gimbal Bearing
Very heavy tool, I was surprised. Pulled my bearing like it was nothing. Putting the new bearing in was a little more difficult as you have to drill a hole in the engine alignment shaft where it will work for your particular outdrive. Not hard, but it does not come pre-drilled as the required depth for each particular gimbal bearing differs by manufacturer and model. Measure your bearing placement before removal and check that it was installed correctly in the first place. The bearing should line up with the grease fitting and the o-rings on the drive shaft should end up riding in the middle of the bearing. once you have your measurement drill the hole, I used a drill press. I suppose you could use it on multiple outdrive models as long as you can drill more holes.
WAS THIS REVIEW HELPFUL?YesReportShare
Reviewed in the United States on June 5, 2023
G
Verified Purchase
Greg
Port Orchard, US
★★★★★ 5
Great value
This kit worked perfectly on my Alpha one mercury outdrive. I saw a lot of people mention that it was a hassle to drill the hole when you better have all this alignment stuff. I threw it in use my regular drill drill guide and then the second hole was lined up. Pulling Gimble be very easy. I did have to adjust it up at an angle because my bearing was sitting in their crooked and it came out the second time I made the adjustment to the angle. I would highly recommend this.
WAS THIS REVIEW HELPFUL?YesReportShare
Reviewed in the United States on April 16, 2024

recommand products

GB HOEKANKER ZWAAR 60X100 EV 70X8
103.20
GB GORDINGLAS 75X275 SV 1,5
37.15
GB GORDINGLAS 46X96 SV 1,5
25.96
GB HOEKANKER ZWAAR 100X170 TV 70X10
125.95
GB RAVEELDRAGER MET STRIP 225/50X150 SV 1
115.00